Woodworking guide: Finishing

For dramatic results, it's hard to beat the finishing process. With the first touch of a rag or brush, your furniture piece comes alive and the true character of its wood grain jumps out at you. Gone is the well-sanded but relatively neutral surface of the raw stock. And if you have any doubts about whether all the work was worth it, those will probably disappear, too.


The first step in the process is to pick a suitable finish. Many products are available with varying characteristics. But the one thing they all have in common is protection. All are designed to inhibit the transfer of moisture and to prevent the surface from being contaminated by dirt and stains


The most common finishes are shellac, lacquer, varnish and oil. All are solvent- or oil-based products and therefore require some precautions. Wear protective gloves, goggles and a respirator with organic vapor cartridges when using these materials. And make sure your work area is ventilated according to the recommendations printed on the product's container.


One of the biggest differences among these four traditional finishes is how they function on wood. Shellac, lacquer and varnish are all surface finishes. This means that they do not penetrate, to any great extent, past the surface of the wood. The first coat certainly goes in the farthest, but subsequent coats merely build on the first to form a smooth, usually glossy, surface. Oil, on the other hand, is considered a penetrating finish because it reaches much deeper into the wood and leaves only a microscopic layer of finish on the surface. Subsequent coats continue to penetrate.


All these finishes have their strengths and weaknesses. Shellac, for instance, is a wonderful product. When properly applied it creates a stunning high-gloss surface which over time takes on a remarkable amber color. It's also very fast-drying, which is a great advantage over some other finishes. Unfortunately, shellac is very prone to water stains.


Lacquer is also quick-drying and is the preferred finish of many professionals. It's usually sprayed on and yields a clear, hard finish that stands up well to practically any abuse. It is, however, very flammable


Varnishes, both the traditional types and the newer polyurethane versions, are extremely durable and some impart a warm amber tone, not unlike shellac. Unfortunately, varnish can be difficult to apply and it takes a very long time to dry. Because of this, airborne shop dust becomes a real problem. It settles in the finish before the finish is dry. Then it has to be rubbed out before another coat is applied.


For the beginner, an oil finish is the best choice. It's easy to apply, dries fairly quickly and is not difficult to repair. It also imparts silkiness to the surface and develops a beautiful patina over time.



Preparation


Of course, proper surface preparation is one of the keys to good finishing. And the only way to get it is by sanding. For the best results, you should work through a sequence of abrasives, starting at 120-grit and moving to 150-, then to 180- and 220-grit, finishing up with 320-grit. (This process is described in more detail in "Abrasives") Always dust off the piece thoroughly before moving to each new grit and ease any sharp edges by hand sanding (Photo 1). Once you're done sanding be sure to wipe off the entire piece with a tack cloth (Photo 2) or a rag that's been slightly dampened with linseed oil.



Staining


If you want to alter the natural color of a piece, you must stain or dye the wood. Oil-based stains are certainly the most common approach. These products are available at paint and hardware stores, and at home centers. They contain a pigment that is suspended in an oil and mineral spirits solution. Oil stains don't penetrate the wood deeply. They give color by embedding opaque pigment in the surface grain. You apply these stains with a rag or brush, let them sit for 10 to 15 minutes, and then wipe them off.


Aniline dyes are another approach to coloring wood. The type that is dissolved in water is the safest and easiest to use, as well as being the most colorfast. These dyes penetrate much more deeply than stains and actually change the color of the wood. It's easy to intermix colors and you can change the concentration of color simply by adding more water.


Once you've chosen your coloring method, be sure to test it out on some scrap pieces of stock before turning to your project. Taking the time to get it right is much easier than removing a stain or dye that you don't like.


Applying The Finish


When you're ready to apply your oil finish, be sure to read the manufacturer's instructions carefully, and do what's recommended. While specific directions may vary, there are some general guidelines for applying an oil finish.


Begin by rubbing a liberal amount of oil into the surface of the wood using a lint-free rag (Photo 3). Allow the oil to absorb for about an hour, then wipe off the excess. Let the surface dry for 24 hours, and then rub the whole piece with No. 0000 steel wool (Photo 4). Remove any dust, then apply another coat of oil as before. For a good finish, you should apply a minimum of three coats. Once the last coat is dry and rubbed with steel wool, apply a light coat of paste wax to the entire surface (Photo 5). When the wax takes on a dull appearance, buff the surface to a satin sheen with a clean, dry cloth (Photo 6).

1-Ease all the edges on your project with sandpaper and a sanding block. Work across the grain for best results.




2-When you're done sanding the entire piece, brush off all the dust. Then wipe the entire surface with a tack cloth




3-Apply an oil finish with a lint-free rag. Rub the oil into the wood and let it dry for 1 hour. Then wipe off the excess.




4-Use No. 0000 steel wool to rub the finish between coats. Use a tack cloth to remove all the dust before recoating.




5-Once the last oil coat is dry, apply a light coat of paste wax to your project. Be sure to cover all the surfaces.




6-Let the wax dry until the surface is dull. Then buff the entire piece to a high luster with a clean soft rag.​

​

​

 

This is a very good in-depth guide on how to finish. I've had a woodworking class in the past before, and I've done something similar to this. This has the right steps, clear explanation, and great facts. I love the use of pictures and the steps at the bottom. You may want to add pictures between some blocks of text. Other than that, this is a good guide. 9/10.

 

Thanks hahanerd :]