I made one, then brought it into tech class to show my teacher. Heres some tips.
Stay clear of the combustion potato guns, you know the ones that you spray like propane in and ignite? Thats are just and they are very inconsistent, sometimes I was able to put massive dents in my shed other times it wouldn't even come out of the barrel.
(maybe because I suck at making combustion potato guns lol)
BUT.
I used air compression, much more reliable and its consistent. I built it the same way as you would a normal one, I just tweaked some things.
Heres what I bought, you can have them veiry. IF you really want to make a unique one go to home depot and piece one together wile your there like I did.
But I used from back (chamber) to tip of the barrel.
PSI gauge
Bike tire valve
4" Pcv cap (for the end of the tube)
4" Pvc pipe pipe I used was 1 ft long (smallw was my first)
4" to 3" pvc adapter (to connect the small pipe to the chamber (back pipe)
3" Pvc ball valve (this is basicly a lever you twist it one way and its closed, twist it another way and its open. Thats to hold pressure)
3" to 2" pvc adapter (to connect to the other adapter to put an even small barrel on the gun)
If you dont want to die YOU'LL READ THIS!!!
- Make sure the PVC pipe is rated for pressure, it'll say PSI XXX (how much psi it can withstand. Some of the pieces on mine said 260 other pieces said 320, I never got up to that much psi anyway.
- BUY PVC PRIMER (the primer is usually purple, you put it on before you start glueing the pieces together. IT cleans the pipe.
- BUY PVC GLUE ( dont use crazy clue or some shit like that, but PVC glue lol.)
How I built mine:
1- Pieced together and bought the things listed above in home depot
2- Went home told my mom I wasn't going to lose a limb
3- I cleaned the pipes in my bath tub (just to make sure they were free from dirt)
4- Drill a whole in the PVC cap thats a little smaller then your bike tire valve
5- force the valve into the little whole from the inside until its snug (shouldn't leak air you'll know why when you see it)
6- take your cap slide it on the 4" pipe to get an idea of where it'll stop going in. Then take it off
7- Drill a whole a little smaller then your PSI gauge, then take plumbers tape, wrap it around a little and tap it into the hole.
8- You should screw a nut on from the inside of the chamber on to the gauge, (later on the pressure could blow the guage out)
9- Prime the inside of the cap
10- Prime the outside of the 4" pipe
11- Put glue on both piece and put pressure on it for like 20 seconds and let it sit for a couple minutes.
12- Attach your 4" to 3" adapter the same way as I told you in steps 9,10,11
13- Attach your pvc ball valve same way I told you above
13- Attach your 3" to 2" pvc adapter to that end same was as before =p
14- Do the barrel the same way (the longer the barrel the farther it Will go, ASLO the small the diameter the more force will push on the potato inside the barrel (or golf balls 2" pvc is pretty good for golf balls)
15- File down the end of your barrel into a tapered sharp point (this will shave the access potato off to make an airtight seal)
16- ONE OF THE most important steps, DO NOT SHOOT THE GUN RIGHT AFTER making it. You have to let the glue stiffen up so wait like 24 hours.
Now you'll think this air compression thing blows because you dont have an air compressor. You dont need one, you can use a bike pump.
Mine was about 4 1/2 ft long, The max PSI I got it fill to was 102 psi. that 102 psi was able to launch a potato 467 ft (we measured it on the football field) That was the furthest distance. If i made it bigger I could have got way more psi in and could have easily launched it over 1000 ft I believe. These things are not toys, you should definatly have a parent or someone with you wile using it. Do not point it ay anyone! It will kill them
MAKE SURE TO USE PRESSURE RATED PIPE!! IF YOU DONT. THE pvc pipe will explode once pressure is introduce and it will blow up making PVC shards (shrapnel) which will defiantly fuck you up.
This is my guide, I made it you will not find it anywhere. I might have missed some things I will edit as I notice them. Any questions just pm me your msn/aim and we can talk.
the whole job will cost you about 35 bucks including primer/glue pipe/gauge.
EDIT: Just made this.
No one better take credit for this guide lol
